Star of David Spinner

I created two versions of this star.  One is a hanging ornament and the other is a desk model.

 Here is the PDF.  It is not a very good PDF as it does not show the lines correctly.  All of the lines are connected except for the center points have a small gap.  This small gap is where the paper is  attached as a whole which allows for the spin to occur.
https://drive.google.com/file/d/0B7oGIyVDbRGYMjdtZm8xdHd4eUE/edit?usp=sharing


Here is the .Studio file. I used cardstock.  Assemble the star as shown in the picture below. Each star goes in the opposite direction to create the spinning effect.
https://drive.google.com/file/d/0B7oGIyVDbRGYRHZlV3IySWRyRUE/edit?usp=sharing




Happy Hanukkah to all my Jewish friends!




P.S.  Check back later as I have quite a few more spinners to post but not enough time.

Comments

Post a Comment

Popular posts from this blog

Rotational Symmetry Explained Using 5 Different Types of Pinwheels

Image
I created five different types of pinwheels to explain the concept of rotational symmetry. Rotational symmetry is when a figure is rotated around a central point and the angle of rotation is noted when the object looks the same as the original figure. For example, a square has 90 degree rotational symmetry because it looks that same at 90 degrees, 180 degrees, 270 degrees and at 360 degrees. The order of rotational symmetry of  a square is 4 because it looks the same 4 times in one rotation around a central point. Here is the PDF of the pinwheels. https://drive.google.com/file/d/0B7oGIyVDbRGYT1duczNleEM4SUU/edit?usp=sharing Here is the .Studio file of the pinwheels.  I would recommend using the thinnest material for the blades and the strongest paper that won't tear easily for the rest of the pinwheel. https://drive.google.com/file/d/0B7oGIyVDbRGYMjAtRWlyZFliT2M/edit?usp=sharing  Paper is not the best material to make the axles of these pinwheels....
Read more

Dump Truck Paper Model

Image
I made this model for Juanita who said she couldn't find a nice model of a dump truck. This truck takes about three hours to construct. Cut out all of the pieces and plan how you are going to construct the dump truck by looking at the photos. I recommend gluing on all of the veneer pieces before constructing the truck. Also bend all of the tabs before trying to glue any of the pieces together. The yellow truck bed should be glued from the top edge first, a few tabs at a time until you get to the bottom of the first corner. Align the rest of the tabs and corners. After all of the corners and edges are aligned, then glue the tabs down. For the cab of the truck, start gluing from the windshield and go downwards.  Glue one or two tabs at a time and let them dry completely before continuing. There are two tabs that meet at the bottom edge of the cab.  The tabs lay on top of one another.  I placed the back piece tab on top of the front piece tab. The cab is glued to the yellow ...
Read more

VW Love Bug Ornament for the Christmas Tree

Image
VW Love Bug Christmas Ornament with a string hangar on top. I made a VW Love Bug for my Christmas tree.  This three inch model reminds me of the time that a friend drove me in his VW Bug with a hole in the floor on the passenger side. The hole was so big that I could see the pavement speeding by at 50 mph. It was a wild ride! The curved tire well pieces are a little hard to put together.  I recommend curving all the pieces to their final form and then gluing them tab by tab.  It is a little tedious but it works. I used cardstock for the model and shiny vinyl for the peace flowers. Here is the PDF. https://drive.google.com/file/d/17lP_S01WW1vbDrCOHJBj3Wg-h5LRV2Ny/view?usp=sharing Here is the .Studio file. https://drive.google.com/file/d/1g-KRolmGfNzAuGPOX3w-8G6SFzdhdjC_/view?usp=sharing  The bumpers are glued on just the ends  undercarriage  Prototype without the string hangar
Read more